Skip to content

How to specify chafing dishes for a hotel buffet

Pan size, lid action, fuel type and how many you actually need per hundred covers — the specification a purchase manager is usually left to guess at.

14 July 2026 · 7 min read

A chafing dish is the most-photographed and least-considered object in a hotel. It is bought on price, replaced on failure, and specified — when it is specified at all — by copying whatever the last property used. What follows is the specification a purchase manager is normally left to guess at.

Start with pan size, not with the dish

Everything else follows from the food pan. The industry standard is Gastronorm, and the two sizes that matter for a buffet are GN 1/1 (530 × 325 mm, roughly 9 litres at standard depth) and GN 2/3. Specify the pan and the dish is decided.

The reason this matters more than it sounds: if your chafing dish takes a proprietary pan rather than a standard GN, you are locked to one supplier for spares for the life of the unit. Ask the question directly — "does this take a standard GN 1/1 pan?" — and treat a vague answer as a no.

Lid action decides your service, not your looks

Lid typeBest forWatch for
Roll-topLong buffet lines where staff and guests pass in one direction. Opens one-handed and stays open.The hinge. This is where a chafer dies. Ask whether the pin is machined or a folded tab.
Hydraulic / gas strutCentrepiece islands. The lid stops wherever you leave it.A strut working at its rated limit will creep shut by year two. Specify one rated well above the lid weight.
Lift-offTight corners and back-of-house. Cheapest and simplest.The lid has to go somewhere. In practice it goes on the counter, which is why lift-off looks untidy at volume.
Glass lidBreakfast and live counters, where the food is the display.Thermal shock. Never run cold water over a hot lid.

Fuel or induction

Gel fuel is cheap, portable and unpredictable. It burns at a rate you cannot control, it needs replacing mid-service, and a guest standing close can smell it. Induction gives you a temperature you set and hold, no combustion, and no consumable.

The practical answer for most properties is both: specify chafers with an induction-compatible base plate and a fuel holder. You run induction where there is power and fuel where there is not — a garden wedding, a power cut, a satellite station across the lawn.

How many do you actually need?

These are working numbers, not a formula, and they assume a two-hour service:

  • One full-size chafer per 40–50 covers per hot dish. A 300-cover wedding with six hot dishes needs six to eight units on the line, not six.
  • One soup station per 100 covers, positioned at the head of the line where the queue forms.
  • Split-pan minis for anything that is a side or a condiment. Running eight small items in full-size pans wastes counter and wastes food.
  • Add 10% for rotation. Something is always being washed, repaired or re-finished.

The four questions to put to a supplier

  1. Which steel grade, and where? 304 for anything food touches. 201 is acceptable in a frame and is a fifth cheaper — but a supplier who will not tell you which is which is telling you something.
  2. How is the hinge made? A machined stainless pin outlasts a folded tab by years. This single detail predicts the life of the unit better than anything else.
  3. Standard GN pans? See above.
  4. What is the spares position in three years? Fuel holders, hinge pins, handles and pan gaskets. If the answer is "buy a new one", price accordingly.

Finish, briefly

Mirror polish looks best on day one and worst on day ninety, because every service mark sits on the surface. A hammered or satin face scatters light in the same way that scuffing does, so marks disappear into it. For a property doing daily volume, hammered is the cheaper decision even when it is the more expensive purchase.

We go into this in more detail in the guide to choosing the metal, and every chafer we make is listed with its full specification inthe chafing dish collection.

Written from the factory floor

Tripadi International is a manufacturer and exporter in Moradabad, India. If you are specifying metalware for a property, we will answer questions whether or not you buy from us.