Stainless Steel
Roll-Top Chafing Dish, 9 L
The workhorse of a hotel buffet line. A counterweighted roll-top lid that opens with one hand and stays open, over a full-size GN 1/1 food pan.
The collection
Everything here is made in our own factory. Filter by category or by metal — or send the whole list to us as an enquiry and we will price it.
Heat that holds, hinges that stay quiet.
Cold held long enough to matter.
Balanced in the hand before it is beautiful on the table.
The frame around the plate.
For the food that arrives at the table, not the buffet.
Height is what makes a buffet look designed.
The small metal on the bar and the table.
By metal
Grade 304 where food touches it. The default for anything that lives in a dishwasher or in the sun.
42 pieces →
Cast, spun and antiqued in house. Warm under low light; the material for a room that wants to look expensive.
8 pieces →
Hand-hammered over a form, always lined in steel. The most photographed metal we work in.
8 pieces →
Everything
Stainless Steel
The workhorse of a hotel buffet line. A counterweighted roll-top lid that opens with one hand and stays open, over a full-size GN 1/1 food pan.
Copper
The same mechanism as our steel roll-top, wrapped in a hand-hammered copper skin. Food never touches the copper.
Brass
A round chafer whose lid rises on a hydraulic arm and stops wherever you leave it. The piece that anchors the centre of a buffet island.
Stainless Steel
A glass-lid square chafer built for induction rather than fuel. Guests see the food; the kitchen sees a controllable temperature.
Stainless Steel
A dedicated soup chafer with a hinged half-lid and a ladle rest, sized for the head of a buffet line where the queue forms.
Stainless Steel
Two 2.5-litre wells under one lid. The condiment and side-dish workhorse of a breakfast counter.
Stainless Steel
A single-bottle cooler with a genuine vacuum gap between the walls. It holds temperature about twice as long as a single-wall cooler and never sweats onto linen.
Copper
A two-bottle bucket in hand-hammered copper with cast brass ring handles. The piece that goes to the table when the order is worth announcing.
Brass
A six-bottle party bath on a cast tripod stand. Floor-standing, so it takes nothing off the bar and nothing off the table.
Stainless Steel
A 1.5-litre bar bucket with a perforated drain insert and matching tongs. Melt water sits below the ice, not in it.
Stainless Steel
A tableside stand that takes any of our single-bottle coolers to serving height. It removes the cooler from the table without removing it from the guest.
Brass
A 14-inch hand-hammered round with a rolled rim. The general-purpose tray a floor uses forty times a day.
Stainless Steel
A 20-inch gallery-rim tray with cast side handles, sized to carry a full in-room dining cover in one trip.
Copper
An 18-inch oval for a whole roast, a whole fish, or a mezze spread. Steel-faced, copper-backed.
Brass
A traditional gallery tray with a pierced and embossed rim, for lobby, turndown and welcome service.
Stainless Steel
A 12-inch round with a bonded rubber deck. The most-replaced item behind any bar, built to stop being replaced.
Brass
A 13-inch hammered charger in antique brass. Thirteen inches of worked metal is the cheapest way a banquet hall doubles its apparent price.
Stainless Steel
A beaded-rim charger, silver-plated over steel rather than over brass — so a scratch shows steel, not yellow.
Copper
A plain, unhammered copper charger. The quietest plate we make and the one that photographs best under warm light.
Brass
A charger masked and plated in two tones — a brass rim around a nickel well, or the reverse. One plate that works with both warm and cool tableware.
Stainless Steel
A 5-litre double-wall bowl that keeps a salad crisp through a two-hour brunch and never rings with condensation on the cloth.
Copper
The classic Indian serving handi, hammered copper outside and stainless inside. Goes from the pass to the table without a transfer.
Stainless Steel
A 500 ml sauce boat with a drip-free lip and an underplate. It pours clean or it is not finished.
Brass
A three-tier stand in graduated sizes. Halves the counter length a pastry display needs.
Stainless Steel
Three graduated risers — 100, 150 and 200 mm — that turn a flat counter into a designed buffet.
Brass
A spun brass cloche with a matching tray. Used for the reveal at the table and for the carry down a corridor.
Stainless Steel
A 6-litre dispenser on a stand with a stainless tap and an ice core. Replaces the jugs, and the labour of refilling them.
Copper
A three-piece 750 ml shaker, copper outside and steel inside, with a built-in strainer that actually seals.
Copper
A 1.5-litre table pitcher, hammered and lined. The piece that sits on the table for the whole meal.

Stainless Steel
A deep oval dish with a domed lift-off lid, set on a wide flat rim that runs out into a flat tab handle at each end. Mirror-polished inside and out.

Stainless Steel
A square tray with a smooth mirror well framed by a hand-hammered rim, the corners drawn gently upward. Made in two sizes.

Stainless Steel
A rectangular tray with a smooth rolled rim and a recessed centre panel worked in a regular beaded pattern. Made in two sizes.

Stainless Steel
A narrow, fully hand-hammered tray with raised long sides and flat open ends, for canapés, breads and a run of small plates. Made in three graduated lengths.

Stainless Steel
A rectangular hand-hammered tray whose short ends draw out into shaped handles cut from the same sheet, with a raised rim on all four sides.

Stainless Steel
A long, narrow dish drawn to a point at one end and swept into a curved tail handle at the other, mirror-polished throughout. Made in two lengths.

Stainless Steel
Three graduated oval trays, hammered across the well, with a plain rolled rim. They nest.

Stainless Steel
Three graduated rectangular trays, hammered throughout, with a raised rim on all four sides and the corners drawn up.

Stainless Steel
A flat serving tray with a wide hammered rim framing a smooth mirror well, made as two ovals and a round.

Stainless Steel
A rectangular hammered tray with a slot cut into the raised rim at each end to serve as a handle. Made in two sizes.

Stainless Steel
A round dish and an oval platter with upswept hammered sides and a smooth mirror floor, deeper than a flat tray.

Stainless Steel
A square tray worked the other way round from most: a hammered centre panel inside a smooth stepped rim.

Stainless Steel
A small narrow tray with a rolled rim and a recessed panel, photographed in two surface treatments — a fine bead and an etched scroll.

Stainless Steel
A plain round platter, mirror-polished, with a narrow rolled rim and no texture anywhere on it.

Stainless Steel
A square tray with a hammered floor and a smooth rolled rim, the corners softened. Photographed as two sizes.

Stainless Steel
A rectangular tray with a hammered floor inside a wide smooth rolled rim, corners drawn up and softened.

Stainless Steel
A large square tray, hammered across the floor, with a smooth rolled rim and softened corners.

Copper
A square tray in hammered copper with a smooth rolled rim — the one piece in this set that is not silver-coloured.

Stainless Steel
A square bowl hammered all over, the four corners drawn upward into points and the sides falling away between them.

Stainless Steel
A shallow leaf-shaped dish with a raised midrib running its length and a fine combed rib radiating from it. Made in two sizes.

Stainless Steel
A shallow triangular dish with a textured well and a smooth raised edge, the corners rounded. Made in two sizes.

Stainless Steel
An oval dish with a hammered well recessed inside a wide, flat, smooth rim. Made in two sizes.

Stainless Steel
A deep square bowl with steep hammered walls and a flat floor, the rim left as a fine plain edge.

Stainless Steel
A long platter drawn to a point at both ends, with a recessed textured well and the edges sweeping up and away.

Stainless Steel
A deep oval dish with a domed hammered lid seated on a wide flat rim, the base left smooth.

Stainless Steel
A square covered dish, hammered on both base and lid, with a fine beaded moulding running around the rim of each.

Stainless Steel
A plain round charger with a brushed face and a narrow plain rim — no texture, no pattern, no applied edge.

Stainless Steel
A charger with a smooth mirror well framed by a rim worked in fine lines radiating out to the edge.

Stainless Steel
A tapered ice bucket, hammered over the body, with a dropped ring handle on each side and a rolled rim.