
Stainless Steel
Oval Covered Serving Dish
A deep oval dish with a domed lift-off lid, set on a wide flat rim that runs out into a flat tab handle at each end. Mirror-polished inside and out.
In use
Three hundred covers, one line, no cold food.
A wedding buffet is a logistics problem dressed as a design problem. The metal has to hold heat for two hours, survive being loaded by staff who are moving fast, and photograph well in a room lit for people rather than for food.
The scenario
A 300-cover reception with a twelve-metre buffet line, live counters at both ends and a dessert island in the centre.
What to specify
The pieces

Stainless Steel
A deep oval dish with a domed lift-off lid, set on a wide flat rim that runs out into a flat tab handle at each end. Mirror-polished inside and out.

Stainless Steel
A narrow, fully hand-hammered tray with raised long sides and flat open ends, for canapés, breads and a run of small plates. Made in three graduated lengths.

Stainless Steel
Three graduated oval trays, hammered across the well, with a plain rolled rim. They nest.

Stainless Steel
Three graduated rectangular trays, hammered throughout, with a raised rim on all four sides and the corners drawn up.

Stainless Steel
A flat serving tray with a wide hammered rim framing a smooth mirror well, made as two ovals and a round.

Stainless Steel
A rectangular hammered tray with a slot cut into the raised rim at each end to serve as a handle. Made in two sizes.

Stainless Steel
A square tray worked the other way round from most: a hammered centre panel inside a smooth stepped rim.

Stainless Steel
A plain round platter, mirror-polished, with a narrow rolled rim and no texture anywhere on it.

Stainless Steel
A square tray with a hammered floor and a smooth rolled rim, the corners softened. Photographed as two sizes.

Stainless Steel
A rectangular tray with a hammered floor inside a wide smooth rolled rim, corners drawn up and softened.

Stainless Steel
A large square tray, hammered across the floor, with a smooth rolled rim and softened corners.

Stainless Steel
A square bowl hammered all over, the four corners drawn upward into points and the sides falling away between them.

Stainless Steel
An oval dish with a hammered well recessed inside a wide, flat, smooth rim. Made in two sizes.

Stainless Steel
A deep square bowl with steep hammered walls and a flat floor, the rim left as a fine plain edge.

Stainless Steel
A long platter drawn to a point at both ends, with a recessed textured well and the edges sweeping up and away.

Stainless Steel
A deep oval dish with a domed hammered lid seated on a wide flat rim, the base left smooth.

Stainless Steel
A square covered dish, hammered on both base and lid, with a fine beaded moulding running around the rim of each.

Stainless Steel
A plain round charger with a brushed face and a narrow plain rim — no texture, no pattern, no applied edge.

Stainless Steel
A charger with a smooth mirror well framed by a rim worked in fine lines radiating out to the edge.
Stainless Steel
The workhorse of a hotel buffet line. A counterweighted roll-top lid that opens with one hand and stays open, over a full-size GN 1/1 food pan.
Brass
A round chafer whose lid rises on a hydraulic arm and stops wherever you leave it. The piece that anchors the centre of a buffet island.
Stainless Steel
A dedicated soup chafer with a hinged half-lid and a ladle rest, sized for the head of a buffet line where the queue forms.
Stainless Steel
Three graduated risers — 100, 150 and 200 mm — that turn a flat counter into a designed buffet.
Brass
A 13-inch hammered charger in antique brass. Thirteen inches of worked metal is the cheapest way a banquet hall doubles its apparent price.
Brass
A spun brass cloche with a matching tray. Used for the reveal at the table and for the carry down a corridor.
Copper
The same mechanism as our steel roll-top, wrapped in a hand-hammered copper skin. Food never touches the copper.
Stainless Steel
A glass-lid square chafer built for induction rather than fuel. Guests see the food; the kitchen sees a controllable temperature.
Brass
A six-bottle party bath on a cast tripod stand. Floor-standing, so it takes nothing off the bar and nothing off the table.
Stainless Steel
A 20-inch gallery-rim tray with cast side handles, sized to carry a full in-room dining cover in one trip.
Stainless Steel
A beaded-rim charger, silver-plated over steel rather than over brass — so a scratch shows steel, not yellow.
Brass
A charger masked and plated in two tones — a brass rim around a nickel well, or the reverse. One plate that works with both warm and cool tableware.
Copper
The classic Indian serving handi, hammered copper outside and stainless inside. Goes from the pass to the table without a transfer.
The metal a guest touches before the food arrives.
Sun, chlorine and salt air are a materials problem.
It travels a corridor, a lift and a threshold.
Trade enquiry
Tell us what you are specifying and we will come back with prices, MOQs and a lead time. If you already built an enquiry list, it is attached automatically.